How to change Elekton SIU setpoints

[ALEngineer]

- Connect a laptop to TMSN-3 SIU (surface interface unit, TMS)
- Run TMCN_Control_v.2.302 Pro.exe
- Open the "setpoints" tab and click the circular-arrow button (left column) to read setpoints.

Change 0x111 "sync-pulse amplitude detection threshold" - default 30; you can lower to 25 or 20.

- Find the row "sync-pulse amplitude detection threshold" (often row 18):
- Enter 25 or 20 in the right column and tick the checkbox.

If within a couple of minutes with the ESP motor stopped there are still no readings, change 0x110 "half amplitude window range" - default 12; you can raise to 14 or 16.

- That setpoint is usually row 17:
- Enter 14 or 16 in the right column and tick the checkbox.

Done. Download the program here (attachment).

Instruction as a separate file (attachment). Not my authorship: Testing VSD RS-485 output to SCADA

Scan / image text translation (original scan kept as attachment below):

2.4.3 When using port "1 RS-232" to connect a PC to the SIU (TMS), use interconnect cable No. 1 TsTKD 083.01-02 made by Elekton. Figure 1 shows the pinout of cable No. 1 for the PC connection.

Figure 1 - Pinout of cable No. 1 (both ends DB9F, X1 and X2):

Code: Select all

Straight-through
  X1 pin 2 -- X2 pin 2
  X1 pin 3 -- X2 pin 3
  X1 pin 5 -- X2 pin 5

Jumpers on each connector
  pins 1, 4, 6 together (DCD / DTR / DSR)
  pins 7 and 8 together (RTS / CTS)
  pin 9 not connected

1-1.jpg

From the Elekton TMS-3 OM page (TsTKD 228 OM) in the screenshot:

Check SIU output data and data to the controller or other devices. In the SIU, check and adjust analog output voltage ranges (10 V, 4 V) to match the VSD analog inputs. Check and correct other downhole monitoring system (TMS) setpoints. Read the internal history. Correct the internal clock (with Elekton-series VSDs the SIU clock syncs to the controller automatically).

ATTENTION: TMSN-3 SIUs are interchangeable. They work with TMSP-3 and TMSP-2 downhole sensors (TMS). They are not designed to work with TMSP-1.

2.4.4 Pump-unit protection from downhole parameters: data update is typically 40 to 55 s. Factory setting for continuous insulation-resistance (Riso) measurement time is 20 s. Set protection trip delays and AR delays to not less than 1 minute.

2.4.5 The downhole monitoring system (TMS) is powered off together with the VSD automation.

1.jpg

Screenshot of TMC (v. 2.3.0.2) Setpoints tab (TMS-3 address 1, COM1 9600). The two registers used in this procedure:

Code: Select all

+--------+--------------------------------------+---------+----------+
| Addr   | Name                                 | Default | Try      |
+--------+--------------------------------------+---------+----------+
| 0x111  | sync-pulse amplitude detection       | 30      | 25 or 20 |
|        | threshold (often row 18)             |         |          |
+--------+--------------------------------------+---------+----------+
| 0x110  | half amplitude window range          | 12      | 14 or 16 |
|        | (usually row 17)                     |         |          |
+--------+--------------------------------------+---------+----------+

The screenshot also lists other setpoints (date/time, Modbus address, RS-232 / RS-485, well/pad/field numbers, Riso / Iu, voltage window, short/open, pressure and motor temperature). Keep the scan for the full grid.

2.jpg

TMCN_Control_v.2.302 Pro.zip

Manual.zip

Original topic

• Подключить ноутбук к ТМСН-3

• запустить программу TMCN_Control_v.2.302 Pro.exe

• выбрать вкладку «уставки», и щелкнуть кнопку с круговой стрелкой (левый столбец) для считывания уставок.
изменить 0x111 "порог обнаружения амплитуды синхроимпульса" - задано 30, можно уменьшить - 25, 20.
• ищем строчку с уставкой «порог обнаружения амплитуды синхроимпульса (это может быть строчка №18):
• на правом столбце вводим 25 или 20, и рядом ставим галочку;
• если в течение Если в течении пары минут при остановленном ПЭД показаний нет, то необходимо изменить:
0x110 "половина диапазона амплитудного окна" - задано 12, можно увеличить - 14, 16.
• эта уставка обычно на строчке №17:
• на правом столбце вводим 14 или 16, и рядом ставим галочку..

Всё
Скачать программу можно тут:

Инструкция скачать отдельным файлом:


Авторство не мое: Testing VSD RS-485 output to SCADA (Region-2000, Telescop, etc.)

1-1.jpg

1.jpg

2.jpg

TMCN_Control_v.2.302 Pro.zip

Manual.zip